{"nid":"2156","uuid":"2316a257-019c-4036-acfb-179e50783c65","vid":"3001","langcode":"und","revision_timestamp":"1656614967","status":"1","title":"U30 factory default instructions","created":"1367330114","changed":"1692131363","promote":"1","sticky":"0","default_langcode":"1","revision_default":"1","revision_translation_affected":"1","path":{"alias":"\/resources\/tech-notes\/u30-factory-default-instructions","pid":"4541","langcode":"und"},"body":"<p><strong>TechNote Onset\u00ae<\/strong><\/p>\r\n\r\n<h2>Recovering HOBO\u00ae U30-WIF from \u2018Factory Defaults\u2019<\/h2>\r\n\r\n<p>Before beginning, please have a printed copy of this document on\u2010hand if possible.<br \/>\r\nApplies to: U30\u2010WIF<br \/>\r\n<br \/>\r\n<strong>Problem:<\/strong> The U30\u2010WIF (Wi\u2010Fi version) has accidentally been restored to Factory Defaults, which are not the Onset factory defaults. Instead, this causes the Lantronix Wi\u2010Fi module contained in the U30 to be restored to its factory defaults, which are not compatible with the U30.<\/p>\r\n\r\n<p><strong>Background information:<\/strong> The main issue is the Lantronix module\u2019s factory default serial protocol is 9600 baud with no flow control as compared to 115200 baud with hardware flow control.<\/p>\r\n\r\n<p><strong>Solution:<\/strong> Use the HOBO NetSetup utility to reconfigure the U30 as instructed below.<\/p>\r\n\r\n<p><strong>Materials needed:<\/strong> computer, Type A to mini\u2010B USB cable, \u2018HOBO NetSetup\u2019 utility (downloaded from Onset website to computer)<br \/>\r\n<br \/>\r\nIf you make a mistake in entering any of the information, simply repeat that step when presented with the main menu again. There should be no need to power down the device or terminate the program prematurely.<\/p>\r\n\r\n<p><strong>Procedure:<\/strong><\/p>\r\n\r\n<ol>\r\n\t<li>Power down the U30. Important: Unplug any solar panel or AC adapter before unplugging the battery to prevent possible damage to the U30.<\/li>\r\n\t<li>Connect the U30 to the PC via USB cable (type A to mini\u2010B).<\/li>\r\n\t<li>Run the \u2018HOBO NetSetup\u2019 utility (do not click \u2018Begin\u2019 on startup window until step 5).<\/li>\r\n\t<li>Power up the U30 and wait for the PC to detect device. You will hear a sound once detected.<\/li>\r\n\t<li>Now click \u2018Begin\u2019 on the \u2018HOBO NetSetup\u2019 utility startup window. Wait for the text to stop scrolling and the \u2018Change Setup\u2019 menu to appear (see figure 1).<\/li>\r\n\t<li>Type \u20181\u2019 and press \u2018Enter\u2019 to bring up the Channel 1 settings screen (see figure 2).<\/li>\r\n\t<li>Starting with \u2018Baudrate,\u2019 key in and press \u2018Enter\u2019 for each value shown in parentheses in figure 2. NOTE: For all screens in this procedure, any value shown in boldface is particularly critical. After the last value has been entered, the \u2018Change Setup\u2019 menu will reappear.<\/li>\r\n\t<li>Type \u20182\u2019 and press \u2018Enter\u2019 to bring up the Channel 2 settings screen (see figure 3).<\/li>\r\n\t<li>Key in and press \u2018Enter\u2019 for the one value shown in figure 3. Again, you will be returned to the \u2018Change Setup\u2019 menu.<\/li>\r\n\t<li>Type \u20185\u2019 and press \u2018Enter\u2019 to bring up the Expert settings screen (see figure 4).<\/li>\r\n\t<li>Again key in and press \u2018Enter\u2019 for each value shown in parentheses.<\/li>\r\n\t<li>At this point, the device has been reconfigured to an operational state. To save the changes in the device, enter \u20189\u2019 at the \u2018Change Setup\u2019 menu to \u2018Save and exit.\u2019 The \u2018HOBO NetSetup\u2019 utility will automatically terminate.<\/li>\r\n\t<li>From here, the device still needs to be configured to be able to attach to your network. Run the \u2018HOBO NetSetup\u2019 utility again and navigate through options \u20180\u2019 and \u20184\u2019 to configure your server and WLAN as necessary. The options can be seen in figures 5 and 6, although your resulting configuration may differ depending on DHCP settings and network parameters.<\/li>\r\n<\/ol>\r\n\r\n<p>Sample utility screens depicted below: <\/p>\r\n\r\n<p>Change Setup:<br \/>\r\n<br \/>\r\n0 Server<br \/>\r\n<br \/>\r\n1 Channel 1<br \/>\r\n<br \/>\r\n2 Channel 2<br \/>\r\n<br \/>\r\n3 E\u2010mail<br \/>\r\n<br \/>\r\n4 WLAN<br \/>\r\n<br \/>\r\n5 Expert<br \/>\r\n<br \/>\r\n6 Security<br \/>\r\n<br \/>\r\n7 Defaults<br \/>\r\n<br \/>\r\n8 Exit without save<br \/>\r\n<br \/>\r\n9 Save and exit Your choice ?<\/p>\r\n\r\n<p><br \/>\r\n<strong>Figure 1: \u2018Change Setup\u2019 Options Menu<\/strong><br \/>\r\n<br \/>\r\nRev. A Page 1 of 2<br \/>\r\n<br \/>\r\n13Aug2008<br \/>\r\n<br \/>\r\nTechNote Onset\u00ae<br \/>\r\nRecovering HOBO\u00ae U30-WIF from \u2018Factory Defaults\u2019<br \/>\r\n<br \/>\r\nBaudrate (115200) ? I\/F Mode (4C) ?<br \/>\r\nFlow (02) ?<br \/>\r\n<br \/>\r\nPort No (10001) ?<br \/>\r\nConnectMode (14) ?<br \/>\r\nSend '+++' in Modem Mode (N) ? Show IP addr after 'RING' (N) ? Auto increment source port (N) ?<br \/>\r\n<br \/>\r\nRemote IP Address : (000) .(000) .(000) .(000)<br \/>\r\n<br \/>\r\nRemote Port (0) ? DisConnMode (00) ? FlushMode (04) ? DisConnTime (03:00) ?: SendChar 1 (00) ? SendChar 2 (00) ?<\/p>\r\n\r\n<p> <\/p>\r\n\r\n<p><strong>Figure 2: Channel 1 Settings<\/strong><br \/>\r\n<br \/>\r\nBaudrate (00) ?<br \/>\r\n<br \/>\r\n <\/p>\r\n\r\n<p><strong>Figure 3: Channel 2 Settings<\/strong><br \/>\r\n<br \/>\r\nTCP Keepalive time in s (1s \u2010 65s; 0s=disable): (45) ? ARP Cache timeout in s (1s \u2010 600s) : (600) ?<br \/>\r\nCPU performance (0=Regular, 1=Low, 2=High): (1) ?<br \/>\r\n<br \/>\r\nDisable Monitor Mode @ bootup (N) ? HTTP Port Number : (80) ?<br \/>\r\n<br \/>\r\nSMTP Port Number : (25) ?<br \/>\r\n<br \/>\r\nMTU Size (512 \u2010 1400): (1400) ? Enable alternate MAC (N) ? Ethernet connection type: (0) ?<br \/>\r\n<br \/>\r\n <\/p>\r\n\r\n<p><strong>Figure 4: Expert Settings<\/strong><\/p>\r\n\r\n<p>Network mode: 0=Wired Only, 1=Wireless Only, 2=Bridging(One Host) (1) ?<br \/>\r\n<br \/>\r\nIP Address : (000) .(000) .(000) .(000) Set Gateway IP Address (N) ?<br \/>\r\n<br \/>\r\nNetmask: Number of Bits for Host Part (0=default) (0)<br \/>\r\n<br \/>\r\nChange telnet config password (N) ? Change DHCP device name (not set) ? (N) ?<br \/>\r\n<br \/>\r\n<br \/>\r\n<strong>Figure 5: Server Settings<\/strong><br \/>\r\n<br \/>\r\nTopology: 0=Infrastructure, 1=Ad\u2010Hoc (0) ? Network name (SSID) (U30Testing) ?<br \/>\r\n<br \/>\r\nSecurity suite: 0=none, 1=WEP, 2=WPA, 3=WPA2\/802.11i (2) ?<br \/>\r\n<br \/>\r\nDisplay current key (N) ? Change Key (N) ?<br \/>\r\n<br \/>\r\nEncryption: 0=TKIP, 1=TKIP+WEP (0) ?<br \/>\r\n<br \/>\r\nTX Data rate: 0=fixed, 1=auto fallback (1) ?<br \/>\r\n<br \/>\r\nTX Data rate: 0=1, 1=2, 2=5.5, 3=11, 4=18, 5=24, 6=36, 7=54 Mbps (7) ?<br \/>\r\nEnable power management (Y) ?<br \/>\r\nFigure 6: WLAN Settings<br \/>\r\n<br \/>\r\nRev. A Page 2 of 2<br \/>\r\n<br \/>\r\n13Aug2008<br \/>\r\n<br \/>\r\n <\/p>","associated_products":["U30-ETH","U30-WIF"],"brand":"HOBO","documentation_hoboconnect":"0","documentation_intemp_app":"0","documentation_is_datasheet":"0","files":{"download_file":"https:\/\/dev-d9.onsetcomp.com\/sites\/default\/files\/resources-documents\/Portrait_U30-WIF_Recovering%20from%20Factory%20Defaults_Rev%20A_0.pdf"},"FIELDS":[["field_download_file","entity_reference","document"]],"meta_tags":"a:1:{s:6:\"robots\";s:7:\"noindex\";}","resource_topic":["Getting Started"],"resource_type":"Tech Note","tech_note_type":["Hardware Training"]}